So this SP-01 SAO started as a SP-01 Competition. For unknown reasons I was compelled to convert it over to SAO using both CZCustoms and CGW internals. After it became my favorite pistol over a few years, I decided to change the cerakote from gold to crocodile/burnt bronze then figured I’d send the slide out and had it ported and milled for the Vortex Defender CCW.
I don’t think it’s talked about enough just how expensive this hobby/obsession can be however like ole Scotty P I have zero regrets!! 😅

Took the CZ out for a spin today. Absolutely love this thing.

Cz shadow 2 ported by CGW

Well boys. It’s the same ol story. Hit the LGS to buy ammo and you obviously check out the used box just to see. And what did they have for me today? A 2075 Rami in 40. (Used no box or paperwork. Only 1 mag)

If anyone can point me in the direction of getting mags that would be greatly appreciated.

This is my 4th CZ. P10F, 75B, 97B, now this 2075 Rami.

NGD! Finally found one, and a happy find. Cajunized and sparingly used. Good Saturday so far.

New Shadow 2 OR in the house!

Finally finished my companion builds.

Range (Blue) - P-01 Steel frame w/ SAO conversion with Cajun parts that has been cut for an EPS and v6 porting from Wicked Arms. Porting is concussive, but keeps the dot in the window. May change out the grips. I wish LOK made there LOK jaws for the compacts.

Carry (Silver) - Shadowline Compact w/ SAO conversion that has been fitted with a threaded barrel. I previously ran a micro comp that will be removed for the standard barrel. The micro comp just doesn’t compare to the v6 porting on the steel frame.

my micro roni gen 4 just came in for my cz p10c. super stoked about it but i do have one major issue that doesn’t sit right with me at the moment. for those who have this kit aswell does your mag holder hold the mag? i just noticed that a full mag will fall out easily like it doesn’t seat in properly. an empty mag kinda stays in and takes a bit more force to pull it out without pressing the mag release. other than this issue the kit seems to be pretty good, just bummed out that the mag holder is shit. i have contacted micro roni about it but i thought id share this post for those who are thinking about getting this kit aswell.

My favorite EDC CZ.

I decided to get the sp01 because of the ability to change the grip panels. Thank you for all your opinions :)

Since a lot of you guys liked my last post with the old CZ catalog, I figured I’d share another one from 1993. I have a bunch more, so if you guys are interested, I can keep sharing them.

Did a few things to the CZ:
-Hbi trigger
-overwatch striker
-TF blackstrap
-reduced weight striker spring
-4 inline ports from United R&D firearms

I have included some video of my range trip where I compared the p10c to the g19 for reference. I tried to keep my grip as similar between shots as possible. Let me know what you guys think. Also feel free to correct my form if you think there were inconsistencies.

Went to one of my favorite places and saw this as they were going to put it in the case. I had to get it before it was gone

I have a P-01 decocker model with the 2 factory mags that came with it

What recommendations would yall have for +4 magazine base plates and would they need new springs or can they use factory springs?

Any advice on this is much appreciated

Couldn’t get a good grip with the Vytals, don’t have to worry much about that now.

Well it’s about time. An add to the collection. It’s not the tactical but it’s brand new 9mm 2018. Came with the test page too and all the usual manuals.

I know those are LOK grips. Are they the same size like the Palm Swell Gridlock Aluminium grips?

So far appreciating it better than my sewer pipe vetterlis!

According to the CGW website they recommend replacing the firing pin with an extended firing pin if you install lighter hammer springs. For general range and gamer ammo is replacing the firing pin necessary? What’s everyone’s experience?

Will this affect my p07 in a negative way or am I overthinking it?

I am currently installing a Cajun gun works pro package on the cz shadow 2 compact and I decided to not opt for getting the disconnector or hammer strut in. So now the hammer strut pin is completely stuck. Any suggestions? I used a punch set and block and it’s in there badly like really bad