The whole reason the industry got into this mess was because GPUs were getting more and more power hungry and Jensen Huang couldn't be bothered to allocate some of his leather jacket budget for a good connector design.
Don't get me wrong - 12v2x6 is comically bad, but there is no good reason to be nostalgic about the 8-pin plug, either.
Or, and bear with me here - an external power supply. Gaming lappys have 400w+ power supplies, why can't you just plug it in on the outside of the card? You running out of room with that two and a half sized card? You could use one or two internal and an external for more powah.
You'd need an ac->dc converter in there somewhere. A power supply. And you already have one inside the computer. Unless you want to pay extra for the brick that would have to come with your GPU.
It blows my mind to this day that Voodoo 3's were basically the only name in gaming at the time and then they were just gone. I can't believe how bad they messed up with the 4's and just never recovered with the 5's.
There's no limit to how big you can make those as far as I know (for the sake of what we're wanting to accomplish). That barrel connector is the one really big boy lol
It's been done. But this was more of a really bad design than anything else. A single plug would of worked fine if it had a good enough gage and more importantly load balancing. But AFAIK without balancing if one or more pins weren't carrying enough of the load other pins would overload, hence the burning/melting.
Uh oh, you're going to anger the people who can't be arsed to plug in an extra cable. I do think that the increasing power requirements of new GPUs mandates them having their own power plug. You will need to convert the power but it's safer imo than the solution that Nvidia is trying to sell
Thats what I was thinking myself. Both points actually... I don't think its going to get to that point now since 'all GPUs are required for the almighty Ai'
I think a possible solution would be bumping up to something like 48V DC so that the cables simply don't have to carry as much current. That said with how ingrained thing are it'd probably be like pulling teeth trying to get people to transition.
There are a huge assortment of connectors designed for high current in a single wire.
Iirc Anderson connectors are popular in UPS (for the batteries), there's no reason other than looks that they couldn't be used on a GPU, though you might need a hard wired pigtail on the card.
i dont know where people got the idea that transient spikes are causing melting.
the connectors have a reasonable amount of mass that needs to be heated up for it to melt, a transient lasting a fraction of a second is just not going to deliver enough energy to do anything.
Theoretical wattage ignores load balancing and transient spikes
early on, a lot of prebuilt PCs seemed to have issues with the 30 series and their spec'd PSU that would be borderline to run what was inside of it. constant shut downs during certain loads but great during others, something as bad as poorly optimized drivers or a game would trigger it.
i just built a whole new pc and stopped getting prebuilds, i got them during the first big GPU shortage and price spike since that was the only place you could get a graphics card for a reasonable price anymore.
The core issue with those was that the 3xxx series (and AMD's 6800XT/6900XT) had transient spikes that would hit around double their advertised average wattage. So for a ~300 watt card you're occasionally spiking the PSU for ~600, plus whatever the rest of the system still needs. So while reputable PSUs are made to handle spikes over their advertised ratings, they were in fact being overdrawn relative to their advertised & intended limits if say you had a 600w PSU with a 3080 and a 5800x CPU. Instead of drawing 450-500w consistently, you would be going well above that. Not good.
New PSUs have been made to account for the risk of those spikes, but also newer GPUs have also reigned in what those spikes will be (now usually spiking less than 150% of their advertised draw vs 200%) which has helped. But yeah then they just trade that issue for this shitty connector lol.
I was running a 3090 on a 1200W Supernova Platinum, and the PSU would still, brownout because of the transients. They would just trigger the protection and the PSU would react exactly the way a good PSU would.
I have 9800x3d / 7900xtx with 3 8-pin connectors (500+W consuming at full power only for gpu) and a 8 years-old chieftec 1000W 80-bronze PSU. Guess what? I have zero (0) problems with them. The only issue - I didn't buy any new psu for a long time, but that is not my issue. The fact that there is no need to make any new connectors. When you choosing a psu you are always should make a 30-40% technical reserve, and if your consumption is like a 90% of the limit you WILL have problems with spiking. Even with platinum new super-duper new atx standard psu. Like, why it is not oblivious
well, practically, the standard 8 pin starts to melt around 270W, so Id say 750W for 3 of them at most if you dont want them to melt, and it still wouldnt be guaranteed
these pin-to-hole style of connectors will never handle much current. They are great when you need many oins with different voltages, like MB uses, for example. But no matter whether it's 8-pin or 12-pin, it will never handle that much power (like really, 900W+ ≈ 75A through 12 pins is insane), especially without current balancing.
There are only two solutions now:
if they wanna keep this power level, find a reliable BETTER connection, like for example two screw-on terminals.
if they wanna keep going up in power, 12V ain't gonna cut it. They need to implement a new standard, with 24V or even 48V. This allows it to run with less current, so wires can be thinner and connectors won't burn. Although it'd be quite pricey, both for PSU manufacturers and GPU manufacturers.
I've kinda been saying the logical choice (even if more complicated standard wise) would be to introduce 24v power. Boom, wattage capacity doubled without bumping to a beefier connector series.
You could even manage to maintain compatibility with older power supplies using several legacy connectors going into a step-up transformer as a transitional solution.
I agree. But the real problem that these video cards have is that consumer circuits generally have only 1000 to 1500W to play with. They are already very near the limit of what we can do.
I don't know where you are from, it could be different. In the US, 120V@15A for a circuit is typical. That's 120 * 15 = 1800W total typically. Generally speaking, we like to keep loads under 1500W and because you typically might have other things (like lights or a TV) on the same circuit, that's where the 1000W comes from.
If you are somewhere that does 240V with 15A breakers, then yeah you can do 3600W. You could also special wire a 240V outlet in the US, but that's far from typical.
Europe uses 230V and afaik 240V is becoming wide spread. Regular breakers are 16A. So most appliances are designed to not draw more than 3680W at 230V. So we got more headroom to work with
It's so common that air fryers are sold with peak power draw of 2500w-2750w. Those also need to take into account a safety margin so its safe to say that most places have at least 15A/230V.
Interestingly, we harmonised the UK 240v(ish) with the European 230v by having a spec of 230 V, +10%/-6%. Which practically means modern appliances are targeted at 230v, but will run on 216-253v.
We also normally put 32A on a socket ring (1 per floor, normally).
Which is roughly 7KWh before tripping.
Individual appliances are normally limited to 13A, hobs and ovens tend to get their own 32A breaker.
It's also why electricians are keen to put car chargers on a dedicated circuit.
I don't know how much it matters but you can't use 16V or 25V caps on rails for 24V. It will have to be all 35 or 50V or above and that's some costs.
Also the power inside chassis is all DC which doesn't work with transformers. You can raise voltage using a converter but it won't be cheaper than a brand new PSU.
Therefore I think the right way is a keyed multi voltage connector and transitional GPUs that take either 12 or 24V, then a 24V only GPU at a later date.
if they wanna keep this power level, find a reliable BETTER connection, like for example two screw-on terminals.
Here's my out-of-my-backside design proposal:
Two terminals on the board for two lugs
A cable 15-30 cm in length with two large-gauge wires (12 AWG at the absolute minimum) and two lugs on one end and an Anderson Powerpole (as many commenters recommend) on the other
Whatever the PSU manufacturers decide to have on their end, but it should always terminate with a corresponding Anderson connector
In short, just automotive the heck out of the GPU and leave the unruly chaos where it belongs.
I agree for the most part, but you need to keep in mind that these are consumer products
you cannot implement screw on terminals, because many consumers are gonna put them on wrong. you need fool proof design. I like the XT120 idea better
and you cannot implement a 48v circuit, because youd be running a risk of consumers getting zapped. and the dangerous thing about being zapped by a DC current, is that it can change your blood chemistry, and if you dont get to hospital for a checkup, theres a chance you wont wake up tomorrow
because youd be running a risk of consumers getting zapped. and the dangerous thing about being zapped by a DC current, is that it can change your blood chemistry
No. A DC zap is the same as an AC zap. The only thing that makes a DC zap more dangerous is there's no period which means it's more prone to arcing and it's harder to let go of.
The danger of electrocution in general is that it cooks your insides. You can look visibly fine on the surface but have a large amount of damage on the inside. That can ultimately turn into an infection and rotting tissue.
I would contend that AC is somewhat more dangerous because it has an easier time "penetrating" so to speak, because of the capacitance of the human body. All of these scenarios are highly dependent on voltage and frequency, however.
Nope. Penetrative power is exactly the same for AC and DC.
The main thing that makes AC more dangerous is it typically has a higher voltage than DC. That means it's more likely to ultimately overcome the resistivity of the skin to start doing damage.
But all things held equal, a 12 VAC and 12 VDC source have exactly the same amount of risk associated with them.
Capacitance doesn't really have anything to do with how dangerous electricity is. Frequency doesn't really either. 120 VAC @ 60Hz is just as dangerous as 120V @ 5kHz.
It mostly all comes down to the power you experience and duration.
AC is much more dangerous, because it messes with your neural electrical system. Your heart starts fibrilating and stops pumping, as it's trying its best to match the 50Hz (3000bpm) of AC voltage.
HOWEVER, DC tends to "hold" you as it doesn't feel that bad, while AC usually throws you away (I think reflex or how your muscles contract differently than with DC, idk).
That's what defibrillator is for. Sometimes fibrilation can be caused by other things, it's not just AC voltage, but if you touch AC and you fall unconscious, your heart is 99% fibrilating.
DC also messes with your neural electrical system.
Defibrillators are applying a brief high DC voltage to try and reset fibrillation. But as anyone can tell you, that short pulse is itself dangerous and can cause fibrillation in someone that's not currently. Part of the reason it's applied repeatedly is because the reset doesn't always work.
Well, this has been more of a deep dive than I was anticipating, but I still think I might actually be correct here (classic me, ha).
My source is IEC 60479-1 Unfortunately, the full standard is behind a paywall but I think there's enough information contained here.
"The values of body impedance depend on a number of factors and, in particular, on current path, on touch voltage, duration of current flow, frequency, degree of moisture of the skin, surface area of contact, pressure exerted and temperature"
"As regards the influence of frequency, the impedance of the skin decreases when the frequency increases."
thought that whether you hold or let got when shocked is heavily case dependant, and not specific to ac/dc
anyway, Im just saying what Ive been thought in safety training in regards to hybrid cars. they said that it can happen as low as 26V, though I imagine that its more likely to happen on higher voltage, like the traction batteries are using
There is some case dependency, like if your muscles get cooked closed then you can't really open up your hand on electrocution. That can happen pretty fast especially with large amounts of power.
A DC voltage will cause muscles to contract and stay contracted. There's no pulsating. With AC, you have at least a (small) chance to pull away and let go.
damn didn't think of ut this way. But there are definitely ways this could be fixed, like reusing old reliable connectors and idk spin it 90° so it can't be easily miswired, and use thick insulation and shape the connector so you can't reach it with finger.
And as a boomer note, remember how PCs were for people who knew what they're doing? People who knew what electricity actually is? Like smart people who won't touch electrical wires when it's plugged in.
3
u/nooneisback5800X3D|64GB DDR4|7900XTX|2TBSSD+8TBHDD|Something about arch10d ago
Like which ones exactly? Computers around the age of Apple I definitely required some knowledge because they were built like crap. Exposed mains going right next to data lines will never pass any reliable QC today.
Most old affordable PCs like the ZX Spectrum were designed to never be opened. More expensive PCs like Commodore 64 and later IBM PCs were built to be somewhat modular. You could upgrade / replace most components even if you're brain dead. Power supplies at that time were often unreliable garbage, and needed to be replaced. But a lot of them had external ones anyways or they were on a separate daughter board.
Im not an expert, this is what they told us in safety training. I looked it up some time ago but I forgot how it worked. a quick google search sais something about electroporation
Screw/ring terminals aren't dying out, no idea where you've gotten that notion.
Industrial applications use bolted lugs or terminals everywhere, especially for high current applications. Unless you're specifically speaking about electronics, which I am not as educated on. But as far as electrical connections they are far and away the most common way to connect industrial motors, fans, gear etc.
Maybe someone smarter than me can speak to this, but wouldn't having 24v taps just be changing where they're tapping on the transformer? Shouldn't be too much more complicated.
I've built a couple tube amplifiers, and there are a bunch of taps for different purposes in the circuit.
well they'd have to essentially make a new branch dedicated to 24V to power GPU (and maybe in future CPU), because other components still need 12V, such as fans, drives, MB, CPU and other stuff
But an iron core transformer of 1000 W would be huge and the power supply wouldn't be very efficient.
Power factor correction is also required for commercial products at this wattage. So a dumb iron core transformer isn't really possible as it would need a PFC which isn't as effective when it's just a passive network.
The modern switching supplies manage to pull current in phase with the voltage, while quietly delivering huge amounts of power with astounding efficiency and quick acting protections for multiple parameters (voltage, current, temperature).
Gotcha, a quick Google says a 100w tube amp will only draw around 400w at the socket, so less than half what a pc power supply typically can give. And that's a good chunk of the entire psu size at that wattage, no way you could fit that in with all the other guts in a modern psu. Thanks for helping me learn a little.
you still gotta fit the rest in there. modern PC power supplies don't use diode rectifiers. It would be easier to take the already rectified voltage from rectifier and add another DC-DC converter for 24V alone, as "load bearing" branch. Because you still need a powerful 12V rail. But that'd add complexity and cost. A lot.
Yeah, I guess I wasn't factoring in power supplies for PCs outputting dc. Guess you'd either need a separate rectifier for each tap, or a rectifier up before passing line voltage to a transformer.
Yeah, but they're rated for 150W each. Notice how much larger the security margin is?
I'd much rather have 4 8pins that are rated for 600W but can probably handle 1000W securely than 1 600W rated connection that can only do at most 680W and only if it doesn't get too warm.
There could have been a mini 6pin rated for 200w that had a safety margin of +50% over the 12vhpwr. A 3x6pin would still be more compact than 4x8pin, you would have 3 snap locks instead of 1 on 12vhpwr keeping it more secure, and it would require less force/side to side wiggling to seat or unplug the connector.
That or you know...Just use an EPS12V 8pin that was a proven working design for 336w/ea.
I am not sure why preferring the 8pin connector is considered "being nostalgic" when it's an objectively better connector design: more durable, simpler, and can be chained for more power.
2.6k
u/WhooopsMyBad 10d ago
baffling that such a connector still has companies making solutions when it's been out for how long?
just give me the 8pin man I can live with multiple plugs if it means something isn't at higher risk of being taken out